Search found 10 matches

by draco12369
Sat Sep 16, 2006 2:56 pm
Forum: Ignition Setup, Tuning, and Troubleshooting
Topic: Tach jumping around at idle.
Replies: 2
Views: 553

No in MegaTune the RPM is pretty stable.
by draco12369
Tue Sep 12, 2006 7:26 am
Forum: Ignition Setup, Tuning, and Troubleshooting
Topic: Tach jumping around at idle.
Replies: 2
Views: 553

Tach jumping around at idle.

Hi i am running a MS2 Version 3.0 and am using the edis-4 set up. I built the tach output circuit as instructed and when at idle the tach jumps. When im off idle it seems to work just fine, it only acts up at idle. Any suggestions. Do i just need to add a capacitor into the circuit somewhere, or ...
by draco12369
Tue Sep 05, 2006 9:08 am
Forum: Tuning Fuel and Air
Topic: Trouble setting up a toyota motor please help!
Replies: 3
Views: 703

I have them set as low imp. injectors, and also i had to change the wire harness, to fire 1 & 4 and 2&3 injects at the same time. My stock harness had them wired 1 & 3 and 2 & 4 could that be my problem possibly? I figured that if the spark fires 1 & 4 and 2&3 the injectors should be prety much the ...
by draco12369
Mon Sep 04, 2006 12:51 pm
Forum: Tuning Fuel and Air
Topic: Trouble setting up a toyota motor please help!
Replies: 3
Views: 703

Trouble setting up a toyota motor please help!

Hi i am running a MS2 version 3.0 with the EDIS-4 controlling the timing. The motor is a 5sgte hybrid (2.2 L turbo). For the injectors i am running a set of DSM 450cc low imp. injectors. I have set everything up for the EDIS-4 as in the manual. The problem i am having is that after getting it ...
by draco12369
Mon Aug 28, 2006 6:46 am
Forum: Injectors, Fuel & Air Supply
Topic: Question about injector settings
Replies: 3
Views: 782

Question about injector settings

Hi i have a set of DSM 450 cc injectors that are about 3 ohms. When i changed the settings to low impedence injecots in megasquirt the car ran much worse, and i did set them up like the manual stated. I was wonderig should i leave them as high impedence injectors since when they are wired in series ...
by draco12369
Thu Aug 17, 2006 7:42 pm
Forum: Tuning Fuel and Air
Topic: Car runs for 1 second and dies
Replies: 4
Views: 759

I got it to run again all i did was reflash the firmware to the megasquirt and ran from the map that came with the firmware, then fine tuned it from there. Hope that helps solve your problem
by draco12369
Thu Aug 17, 2006 9:17 am
Forum: Tuning Fuel and Air
Topic: Car runs for 1 second and dies
Replies: 4
Views: 759

sorry here are the files. There probably is something messed up in the tune file, but the weird thing is that two days ago, i turned on and ran fine but was late so i didnt tune it that night. Next day i went to start it and it ran for a second and died. Any help is greatly appreciated.
by draco12369
Thu Aug 17, 2006 7:42 am
Forum: Tuning Fuel and Air
Topic: Car runs for 1 second and dies
Replies: 4
Views: 759

Car runs for 1 second and dies

I am running a MS2 version 3.0 and have the edis 4 setup on a 4 cylinder. The injectors are 450cc low resistance injecotrs. The fuel pump runs constantly so i have fuel. The car starts up and runs smoothly until about 1000 rpm or one second after it starts and then just dies. I noticed that all of a ...
by draco12369
Tue Aug 15, 2006 6:46 pm
Forum: Ignition Setup, Tuning, and Troubleshooting
Topic: Question about EDIS wheel
Replies: 9
Views: 1684

Thanks for the advice it turned right over!
by draco12369
Mon Aug 14, 2006 10:14 pm
Forum: Ignition Setup, Tuning, and Troubleshooting
Topic: Question about EDIS wheel
Replies: 9
Views: 1684

Question about EDIS wheel

Hi i am running a MS2 version 3.0 and and using the edis4 setup. From the edis page on megasquirt.info i palced my sensor where i understood it shoudl be placed. From my understanding of the page the sensor should be placed 9 teeth before the missing tooth with the motor at TDC of cylinder 1 ...